Author |
Message |
Cw1137
Location: mill creek Joined: Sat Jul 22, 2017 Posts: 1
|
I'm trying to install a free float hand guard on my AR15 but I don't really want to buy a barrel nut wrench to remove the barrel nut that I am never going to use again. Should I go to a gunsmith or is there anyway to do this without buying a special wrench? The hand guard I bought came with a new barrel nut.
|
Sat Jul 22, 2017 2:26 pm |
|
|
Traut
Site Supporter
Location: Downtown Newcastle Joined: Sat Mar 5, 2016 Posts: 3448
Real Name: Traut
|
Welcome to WAGUNS.
Either get or borrow a wrench or take it to a smith. It's not that much money and you can mess up your rifle if you try to fake it. Really. Don't ask how I know. If you were closer you could borrow my wrench. Maybe somebody from the great white north can loan you one.
Good Luck
_________________ I always thought growing old would take a lot longer.....
So, when does that "Old enough to know better" shit kick in??? I've learned that pleasing everyone is impossible, but pissing everyone off is a piece of cake.
|
Sat Jul 22, 2017 2:48 pm |
|
|
Mr. Q
Site Supporter
Location: S. Everett Joined: Thu May 2, 2013 Posts: 3042
|
i have a wrench you can borrow
|
Sat Jul 22, 2017 2:56 pm |
|
|
Yondering
Site Supporter
Location: Skagit County, in the woods Joined: Tue Apr 7, 2015 Posts: 1058
|
You need a wrench, but more than just a wrench; you also need a way to hold the upper receiver. Do not just clamp it in a bench vise.
Gunsmithing requires tools; if you don't want to buy them, you'd be better off taking it to someone who has the tools already.
|
Sat Jul 22, 2017 2:59 pm |
|
|
deadshot2
Site Supporter
Location: Marysville, WA Joined: Fri Jul 22, 2011 Posts: 11581
Real Name: Mike
|
If one is damn careful they can cut the ring off with a die grinder then just remove nut with a pipe wrench. Had to do this when the cheap-assed wrench ended up stripping the teeth off the nut so no wrench would ever work again. I ended up making my cuts with the die grinder on the diagonal times two. Then just broke off the ring. Caution and patience are virtues if going about it this way. To hold the barrel I just took two pieces of oak, clamped them together and used a hole saw just slightly under barrel diameter and cut a hole along the joining surface. When unclamped they fit the barrel pretty snug and when clamped back in the vise with the barrel nestled in the channel nothing went anywhere.
Having the proper tools is the absolute right way but lots of work get's done quite well without them if one is patient and cautious as well as clever.
_________________ "I've learned from the Dog that an afternoon nap is a good thing"
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"For he to-day that sheds his blood with me Shall be my brother" - William Shakespeare
|
Sat Jul 22, 2017 3:01 pm |
|
|
Mr. Q
Site Supporter
Location: S. Everett Joined: Thu May 2, 2013 Posts: 3042
|
oh right, i also have the plastic blocks to clamp the upper....all you need is a vise.
|
Sat Jul 22, 2017 4:34 pm |
|
|
Yondering
Site Supporter
Location: Skagit County, in the woods Joined: Tue Apr 7, 2015 Posts: 1058
|
deadshot2 wrote: If one is damn careful they can cut the ring off with a die grinder then just remove nut with a pipe wrench. Had to do this when the cheap-assed wrench ended up stripping the teeth off the nut so no wrench would ever work again. I ended up making my cuts with the die grinder on the diagonal times two. Then just broke off the ring. Caution and patience are virtues if going about it this way. To hold the barrel I just took two pieces of oak, clamped them together and used a hole saw just slightly under barrel diameter and cut a hole along the joining surface. When unclamped they fit the barrel pretty snug and when clamped back in the vise with the barrel nestled in the channel nothing went anywhere.
Having the proper tools is the absolute right way but lots of work get's done quite well without them if one is patient and cautious as well as clever. He'd still need a wrench to install the new barrel nut.
|
Sat Jul 22, 2017 6:09 pm |
|
|
lunacite
Site Supporter
Location: Snohomish County Joined: Tue Feb 21, 2012 Posts: 1146
|
I'm in South Everett/North Lynnwood if you want to bring your stuff over and we can swap the nut out.
|
Sat Jul 22, 2017 10:21 pm |
|
|
beckdw
Site Supporter
Location: Tri -Cities Joined: Thu May 23, 2013 Posts: 2798
Real Name: David
|
I'm in SE Everett, my neighbors are in mill creek. I have everything you need if you want to swing by. I'm only home on the weekends now though, so some of these other fellows might be better for you.
|
Sun Jul 23, 2017 1:15 am |
|
|
capincurt
Site Supporter
Location: Spokane, WA Joined: Thu Aug 23, 2012 Posts: 997
Real Name: Curtis
|
Pm me if you need the tools or want to swing by to get it done. I am super close to mill creek.
|
Sun Jul 23, 2017 5:26 pm |
|
|
|