WaGuns.org
https://www.waguns.org/

2018 AR-15 Build for a Cause
https://www.waguns.org/viewtopic.php?f=28&t=89796
Page 1 of 3

Author:  BadKarma [ Sun Apr 01, 2018 3:48 pm ]
Post subject:  2018 AR-15 Build for a Cause

With the WaGuns birthday behind us, I would like to take this opportunity to build a gun for a worthy cause. My hope is that we can make a really cool rifle, generate some significant $ for a charity and show our support to others.

Here is my what we have so far.
Image
Image
As of right now, here is what we have.

Aero Lower w/ Laser engraving: Donated by Jaime and Rehv Arms
Fortis LA Stock w/ Buffer Tube: Donated by Steve(yes, the cake eater)
Spoiler: show
Image

Cerakote of Upper, Lower and Handguard to match the stock: Donated by Blown Deadline via Steve (again, the cake one)
Bearcreek Upper: Donated by Jaime
Buffer /w Spring: Donated by Jaime
2 PMAGS: Donated by Caveman Jim
AERO Barrel Nut: Donated by JCrabtree
AR Stoner LPK (basically all the small bits): Donated by Guns4Liberty
PSA complete fire control group: Donated by Guns4Liberty
Magpul MOE pistol grip (black) w/ grip screw: Donated by Guns4Liberty
Magpul MOE trigger guard (black) w/ roll pin, allen screw, & wrench: Donated by Guns4Liberty
AERO Handguard: Donated by old11bravo
Aero 18" Barrel(416R SS .223 Wylde 1/8 twist rifle length gas port) - Donated by Aero Precision USA
BCG and Bolt: Donated by Steve
Muzzle Brake: Donated by RocketScott
Crush Washer for brake: Donated by Jaime
Upper Parts Kit: Donated by Jaime
Charging handle: Donated by san
Erggo Grips: Donated by Pablo
Gas Block and rifle length gas tube: Donated by O_Kellogg

I will update this thread as donated parts become available. I'm also open to ideas. This gun will end up in one of our hands so your input is greatly appreciated.

Author:  dreadi [ Sun Apr 01, 2018 9:00 pm ]
Post subject:  Re: 2018 AR-15 Build for a Cause

I have left over parts from the AR raffle. You don't even need to pry them from my cold dead hands. Mostly small parts, I'll send you a pic.

Author:  BadKarma [ Sun Apr 01, 2018 9:16 pm ]
Post subject:  Re: 2018 AR-15 Build for a Cause

dreadi wrote:
I have left over parts from the AR raffle. You don't even need to pry them from my cold dead hands. Mostly small parts, I'll send you a pic.

Thank you sir. I can ship you my email or send them through FB.

Author:  golddigger14s [ Sun Apr 01, 2018 10:55 pm ]
Post subject:  Re: 2018 AR-15 Build for a Cause

I have a decent butt stock available.

Author:  Massivedesign [ Mon Apr 02, 2018 6:55 am ]
Post subject:  Re: 2018 AR-15 Build for a Cause

golddigger14s wrote:
I have a decent butt stock available.


Somebody hasn’t read the build sheet in the OP. :)

Author:  Guns4Liberty [ Mon Apr 02, 2018 7:17 am ]
Post subject:  Re: 2018 AR-15 Build for a Cause

I have a new-in-package AR Stoner lower parts kit, minus the fire control group and buffer tube assembly. I wouldn't mind donating it to the cause.

I also have a brand new PSA mil-spec trigger that I installed and then removed before ever firing it (came with one of their rifle kits). It's obviously nothing special, but the price is right.

Finally, I have new/never used MagPul MOE parts (pistol grip and trigger guard) that I can throw in to complete the LPK. And I have a PSA carbine buffer and receiver end plate; I just don't have the buffer tube, spring, or castle nut.

Author:  BadKarma [ Mon Apr 02, 2018 11:48 am ]
Post subject:  Re: 2018 AR-15 Build for a Cause

LPK is needed. We have the stock and buffer assembly worked out. Let me know how I can get it from you. Also, thank you for your support.

Author:  Caveman Jim [ Mon Apr 02, 2018 3:01 pm ]
Post subject:  Re: 2018 AR-15 Build for a Cause

Massivedesign wrote:
golddigger14s wrote:
I have a decent butt stock available.


Somebody hasn’t read the build sheet in the OP. :)


Is reading a requirement? I'm just here for the pics. :ROFLMAO: :ROFLMAO: :ROFLMAO:

I can throw in 2 New Pmag 30 AR/M4 gen 2 magazines if needed. :bigsmile:

Author:  old11bravo [ Mon Apr 02, 2018 4:11 pm ]
Post subject:  Re: 2018 AR-15 Build for a Cause

Jaime,

I have an Aero Precision AR15 Enhanced Gen 2 M-LOK Handguard in 15" length. It's brand new but I do not have the BAR nut for it as I intended on attaching it to an enhanced M4E1 upper receiver. I'll donate the rail if you want it. Let me know.

Image

Image

Author:  BadKarma [ Mon Apr 02, 2018 4:33 pm ]
Post subject:  Re: 2018 AR-15 Build for a Cause

old11bravo wrote:
Jaime,

I have an Aero Precision AR15 Enhanced Gen 2 M-LOK Handguard in 15" length. It's brand new but I do not have the BAR nut for it as I intended on attaching it to an enhanced M4E1 upper receiver. I'll donate the rail if you want it. Let me know.

Image

Image

Thank you for the offer. Looks familiar...

Will this work with the bear creek upper though? I thought the “e” versions only mate with the Aero Uppers? I will have to investigate a bit.

Author:  BadKarma [ Mon Apr 02, 2018 4:35 pm ]
Post subject:  Re: 2018 AR-15 Build for a Cause

Caveman Jim wrote:
Massivedesign wrote:
golddigger14s wrote:
I have a decent butt stock available.


Somebody hasn’t read the build sheet in the OP. :)


Is reading a requirement? I'm just here for the pics. :ROFLMAO: :ROFLMAO: :ROFLMAO:

I can throw in 2 New Pmag 30 AR/M4 gen 2 magazines if needed. :bigsmile:

Reading is not a requirement which is why I put pictures. Yes, we could use some mags so the person winning this will have a good start.

Author:  old11bravo [ Mon Apr 02, 2018 6:40 pm ]
Post subject:  Re: 2018 AR-15 Build for a Cause

BadKarma wrote:
old11bravo wrote:
Jaime,

I have an Aero Precision AR15 Enhanced Gen 2 M-LOK Handguard in 15" length. It's brand new but I do not have the BAR nut for it as I intended on attaching it to an enhanced M4E1 upper receiver. I'll donate the rail if you want it. Let me know.


Thank you for the offer. Looks familiar...

Will this work with the bear creek upper though? I thought the “e” versions only mate with the Aero Uppers? I will have to investigate a bit.

It will work fine with a Bear creek upper but as I said, "You will need a BAR nut" to use as the barrel nut. They can be found as cheap as $20 and for as much as $40. It's here if you want it.

Here is a link to a BAR nut for sale at GRO but someone here may have one they could donate too.

https://www.graniteridgeoutfitters.com/Aero-Precision-AR15-BAR-Barrel-Nut-APRH100268.htm

https://webyshops.com/products/aero-precision-aprh100268?variant=3739000799245

This one is $26 but I've never bought from this vendor:

http://mtandgtactical.com/areo-precision-ar15-bar-barrel-nut/

and AP:

https://aeroprecisionusa.com/ar15-bar-barrel-nut.html?avad=48247_d118bc0b1

Author:  JCrabtree [ Tue Apr 03, 2018 8:51 am ]
Post subject:  Re: 2018 AR-15 Build for a Cause

old11bravo wrote:
BadKarma wrote:
old11bravo wrote:
Jaime,

I have an Aero Precision AR15 Enhanced Gen 2 M-LOK Handguard in 15" length. It's brand new but I do not have the BAR nut for it as I intended on attaching it to an enhanced M4E1 upper receiver. I'll donate the rail if you want it. Let me know.


Thank you for the offer. Looks familiar...

Will this work with the bear creek upper though? I thought the “e” versions only mate with the Aero Uppers? I will have to investigate a bit.

It will work fine with a Bear creek upper but as I said, "You will need a BAR nut" to use as the barrel nut. They can be found as cheap as $20 and for as much as $40. It's here if you want it.

Here is a link to a BAR nut for sale at GRO but someone here may have one they could donate too.

https://www.graniteridgeoutfitters.com/Aero-Precision-AR15-BAR-Barrel-Nut-APRH100268.htm

https://webyshops.com/products/aero-precision-aprh100268?variant=3739000799245

This one is $26 but I've never bought from this vendor:

http://mtandgtactical.com/areo-precision-ar15-bar-barrel-nut/

and AP:

https://aeroprecisionusa.com/ar15-bar-barrel-nut.html?avad=48247_d118bc0b1
I'll buy the nut if y'all want to use this handguard.

Sent from my SM-G950U using Tapatalk

Author:  BadKarma [ Tue Apr 03, 2018 3:59 pm ]
Post subject:  Re: 2018 AR-15 Build for a Cause

old11bravo wrote:
BadKarma wrote:
old11bravo wrote:
Jaime,

I have an Aero Precision AR15 Enhanced Gen 2 M-LOK Handguard in 15" length. It's brand new but I do not have the BAR nut for it as I intended on attaching it to an enhanced M4E1 upper receiver. I'll donate the rail if you want it. Let me know.


Thank you for the offer. Looks familiar...

Will this work with the bear creek upper though? I thought the “e” versions only mate with the Aero Uppers? I will have to investigate a bit.

It will work fine with a Bear creek upper but as I said, "You will need a BAR nut" to use as the barrel nut. They can be found as cheap as $20 and for as much as $40. It's here if you want it.

Here is a link to a BAR nut for sale at GRO but someone here may have one they could donate too.

https://www.graniteridgeoutfitters.com/Aero-Precision-AR15-BAR-Barrel-Nut-APRH100268.htm

https://webyshops.com/products/aero-precision-aprh100268?variant=3739000799245

This one is $26 but I've never bought from this vendor:

http://mtandgtactical.com/areo-precision-ar15-bar-barrel-nut/

and AP:

https://aeroprecisionusa.com/ar15-bar-barrel-nut.html?avad=48247_d118bc0b1

Then I will take it sir. looks like we have a BAR on its way too. Thank you sir for your generosity.

Author:  O_Kellogg [ Tue Apr 10, 2018 4:43 pm ]
Post subject:  Re: 2018 AR-15 Build for a Cause

I'll get you a gas block and tube.

Page 1 of 3 All times are UTC - 8 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/