WaGuns.org
https://www.waguns.org/

Local place to get steel to make plates/targets?
https://www.waguns.org/viewtopic.php?f=48&t=94734
Page 1 of 1

Author:  jman308 [ Sun Oct 14, 2018 8:24 pm ]
Post subject:  Local place to get steel to make plates/targets?

Looking to starting plinking steel and build some stands. Are there any places (Pierce co. or South King) that sell and cut?
Reading online it looks like everyone is using the AR500 type steel.

Thanks

J

Author:  NWGunner [ Sun Oct 14, 2018 8:32 pm ]
Post subject:  Re: Local place to get steel to make plates/targets?

Welcome to the Forum! :thumbsup2:

How about Walla Walla?

He ships, though I'm sure the sale is over:

viewtopic.php?f=40&t=54273&hilit=AR500+stand

Author:  usrifle [ Sun Oct 14, 2018 8:40 pm ]
Post subject:  Re: Local place to get steel to make plates/targets?

There are any number of stands available, but you may want to check these guys out for targets too. They aren't that far from you and it's a good cause as well.
http://www.jcsteeltargets.com/

Author:  olydemon [ Sun Oct 14, 2018 8:42 pm ]
Post subject:  Re: Local place to get steel to make plates/targets?

JC targets is a good suggestion if you want a ready made target.

If you want to do it yourself you could try Interwest Metals down in Fife. I know I've seen AR400 plate in the yard...

Author:  toys in the toybox [ Sun Oct 14, 2018 10:38 pm ]
Post subject:  Re: Local place to get steel to make plates/targets?

Can use a thicker standard steel for 22 and most handgun calibers, no need for expensive AR500

most gun shops carry various AR500 plates, no one seems much cheaper than the next guy so give your favorite some business

If ya want a durable stand on the cheap and easy Ive made a few and can help ya out if ya like

Author:  mcyclonegt [ Mon Oct 15, 2018 12:17 am ]
Post subject:  Re: Local place to get steel to make plates/targets?

Also stop by I5 guns in Lacey for a big variety of plates.

Author:  RocketScott [ Mon Oct 15, 2018 7:42 am ]
Post subject:  Re: Local place to get steel to make plates/targets?

I ordered mine from this place:

https://shootingtargets7.com/

I got 5 8" gongs and they threw in a 4" for free. They've held up well

For stands I welded up some rebar that was left over on a jobsite. I was going to make bases for them but pounding them straight into the ground has been working fine

Author:  jman308 [ Mon Oct 15, 2018 10:10 am ]
Post subject:  Re: Local place to get steel to make plates/targets?

Wow thanks for the replies and suggestions. I've seen a variety of stand styles online and most of which I could build.
I'll check out these couple sites and see what they have.

I think the majority of what I'm after is for handgun (dueling plate tree, etc.) or .22 LR.

Author:  oldkim [ Mon Oct 15, 2018 10:19 am ]
Post subject:  Re: Local place to get steel to make plates/targets?

If you can build one... might be a few here interested in sharing the costs.

AR 500 isn’t easy to work with but I hope you know that. It’s not cheap either.

There are ways to get some work done but it ain’t cheap. Best to buy off the shelf from those listed above.

Do you have a design?

Author:  Brokemillwright [ Mon Feb 11, 2019 10:28 pm ]
Post subject:  Re: Local place to get steel to make plates/targets?

I have some 1/2" hardox that I'm thinking of getting rid of if your interested

Sent from my SM-G900V using Tapatalk

Author:  Yondering [ Mon Feb 11, 2019 11:20 pm ]
Post subject:  Re: Local place to get steel to make plates/targets?

jman308 wrote:
Wow thanks for the replies and suggestions. I've seen a variety of stand styles online and most of which I could build.
I'll check out these couple sites and see what they have.

I think the majority of what I'm after is for handgun (dueling plate tree, etc.) or .22 LR.


If you can process it yourself, most fabrication shops should be able to get you a sheet of AR500. I split a sheet with a co-worker last year; we got it at cost through a relative of his that worked in a fab shop. It cost us $500 for the 4'x8' sheet of 3/8" AR500, so for $250 each we both ended up with more target steel than we know what to do with.

For that kind of deal you probably want to split it with a couple other guys, but then the price ends up very reasonable, much cheaper than buying targets if you're willing to do the work. (and it is a fair amount of work, even with a plasma cutter like we used.)

Be a little careful about just using cheap mild steel for handgun calibers - it's fine for 22lr, but will pit and dent with some of the faster handgun rounds. (High velocity is what kills steel, not bullet weight or power; a heavy 44 mag at 1200 fps won't divot steel as badly as say a light 357 Sig at 1700 fps.) For safety, the goal is to have steel that doesn't get deep dents or divots that can direct bullet fragments back at you. 3/8" AR500 is a bit overkill for that, but there are still other reasonably cheap options that are better than mild steel. 1/4" AR400 for example would do what you need and would last pretty much forever even with some of the magnum handgun rounds.

Page 1 of 1 All times are UTC - 8 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/