|
|
|
It is currently Tue Apr 23, 2024 5:30 am
|
RCBS Pro Chucker 5 vs Dillon 650/750
Author |
Message |
lamrith
Site Supporter
Location: Tacoma/Puyallup Joined: Tue May 8, 2012 Posts: 4340
Real Name: Larry
|
MadPick wrote: lamrith wrote: two toolheads setup Silly Dillon people. Even with my far superior Hornady LNL, though, i do two passes with the brass. My process is: Jealousy is not flattering.. MadPick wrote: - Vibratory tumble in corncob to get the main crud off, maybe a half hour. - Lube brass, size/deprime - Wet tumble to remove the lube and make it byooootiful - Trim and/or swage, if needed - Prime, powder and bullet on the second pass through the press.
I do some brass with the X-die so I don't need to trim it, but the process is still the same. I want to be able to remove the lube before I load the case; even with "powder safe" lubes I find them messy, and they attract dirt to the cartridge.
Pretty much the same process I follow. But rather than putting one die in I put a tool head in. I mean who doesn't like more head?
_________________Talons wrote: it's too plastic, even for me. it's like old, overworked, plastic everywhere old pornwhore amounts of plastic.
Last edited by lamrith on Wed Apr 08, 2020 7:58 pm, edited 1 time in total.
|
Wed Apr 08, 2020 11:11 am |
|
|
Yondering
Site Supporter
Location: Skagit County, in the woods Joined: Tue Apr 7, 2015 Posts: 1058
|
Trimming should be a "once every 5-10 loads" thing. If you're having to trim every time, or every other time, you need to re-evaluate your sizing process and die adjustment, and most likely your setup is causing excess headspace as well.
I trim once when I start using new (or once fired, whatever) brass, and then don't trim again until it's been shot a bit. Knowing how long your chamber will actually tolerate, rather than just book specs, is helpful as well; there is a company selling little plugs to measure that, but I forget the name.
Don't over-complicate case prep. Most people invest way too much time in that without additional benefit.
|
Wed Apr 08, 2020 6:24 pm |
|
|
MadPick
Site Admin
Location: Renton, WA Joined: Sun Mar 13, 2011 Posts: 52064
Real Name: Steve
|
Yondering wrote: Trimming should be a "once every 5-10 loads" thing. If you're having to trim every time, or every other time, you need to re-evaluate your sizing process and die adjustment, and most likely your setup is causing excess headspace as well. I don't doubt what you're saying . . . but I think it depends on the rest of your setup. Namely, what kind of trimmer you have and how organized you are with your brass. Personally, I have an awesome trimmer (Giraud Power Trimmer) and shitty brass organization so I don't know how many times each piece has been fired. So, it's easier for me to just trim every time. In fact, it's faster and easier for me to trim than it is to check the length.
_________________SteveBenefactor Life Member, National Rifle AssociationLife Member, Second Amendment FoundationPatriot & Life Member, Gun Owners of AmericaLife Member, Citizens Committee for the Right to Keep and Bear ArmsLegal Action Supporter, Firearms Policy CoalitionMember, NAGR/NFGRPlease support the organizations that support all of us.Leave it cleaner than you found it.
|
Wed Apr 08, 2020 6:38 pm |
|
|
Yondering
Site Supporter
Location: Skagit County, in the woods Joined: Tue Apr 7, 2015 Posts: 1058
|
It shouldn't have anything to do with the kind of trimmer you have set up. The point is to not trim at all except when needed, and to not have a separate brass processing stage.
For example I clean my 5.56 brass, and then load it in one pass in my Dillon 550. I have no reason to do it any other way. I don't need to run it through a separate tool head first or add any extra steps. And that is for match grade accuracy ammo; not cheap junk blasting ammo (I don't waste components and loading time for that). I don't load much 308 on the 550, but treat it the same way when I do.
With pistol calibers, there's no reason to trim or have a processing tool head, unless you found a bunch of crimped primer pocket brass.
|
Fri Apr 10, 2020 4:57 pm |
|
|
|
Who is online |
Users browsing this forum: No registered users and 19 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|
|